Control joints

The JF 1600 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the JF 1600 range are used as control joints with adhesive-laid floor covering such as tiles, ceramics, etc. of 30mm thickness or less. They are suitable for commercial and industrial uses. In general, control joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m.

The JF 1700 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the JF 1700 range are used as control joints with fresh mortar-laid floor covering such as tiles, ceramics, marble, natural stone etc.

The JF 2700 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the Luxe JF 2700 range are used as control joints with rigid floor covering such as marble, granite, natural stone, poured covering, etc. They provide a decorative and luxurious appearance to the floor. In general, control joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m. The joint must reach a minimum depth of 2/3 of the thickness of the floor covering and its substrate mortar, but preferably the total thickness (substrate mortar + covering). It comprises two aluminium side sections available in heights of 20, 30 or 40 mm and thicknesses of 3 or 5 mm, covered with an adhesive expanded rubber, and a coloured silicone joint. Length of 3 m. The edges can be supplied with raw, satin or bright finish. The elastomer is available all the common colours of silicone.

The series JF Deco tile dividers are designed for decorating and dividing floors. They can also be used to get a better protection in accordance with different finishings (mill finish, polished, high gloss polished, etc.). Series JF Deco tile dividers are available in brass, aluminium and stainless steel.

The JF 600 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the JF 600 range are used as control joints with adhesive-laid floor covering such as tiles, ceramics, etc. of 15 mm thickness or less. They are suitable for commercial and industrial uses. In general, control joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m. Made with coextruded PVC with an outer layer of rigid PVC for efficient protection of the tile edges, and a flexible PVC central element able the take up the floor constraints. The joints of the JF 600 range are used essentially for "budget" applications or when aesthetics is not a determining factor. Available in different heights and a length of 2.5 m. The control joints of the JF 600 range are available with long flanges or short flanges, in the standard grey, black and white colours. They can also be made with other heights, in any other RAL colour, and in any other special colour depending on quantity. The joints of the JF 600 range are used as control joints with adhesive-laid floor covering such as tiles, ceramics, etc. of 15 mm thickness or less. They are suitable for commercial and industrial uses. In general, bay joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m.

The JF 700 range of pvc control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints.

PVC control joints for floors made to prevent the malfunctions (cracks, debonding) that systematically occur when flooring systems are installed in large areas without joints. They are used to partition bed affixed floors such as tiles, ceramics, natural stone, etc. The PVC control joints are supplied with stainless steel or brass caps for a more luxurious finish.

The JF 1600 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the JF 1600 range are used as control joints with adhesive-laid floor covering such as tiles, ceramics, etc. of 30mm thickness or less. They are suitable for commercial and industrial uses. In general, control joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m.

The JF 1700 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the JF 1700 range are used as control joints with fresh mortar-laid floor covering such as tiles, ceramics, marble, natural stone etc.

The JF 2700 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the Luxe JF 2700 range are used as control joints with rigid floor covering such as marble, granite, natural stone, poured covering, etc. They provide a decorative and luxurious appearance to the floor. In general, control joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m. The joint must reach a minimum depth of 2/3 of the thickness of the floor covering and its substrate mortar, but preferably the total thickness (substrate mortar + covering). It comprises two aluminium side sections available in heights of 20, 30 or 40 mm and thicknesses of 3 or 5 mm, covered with an adhesive expanded rubber, and a coloured silicone joint. Length of 3 m. The edges can be supplied with raw, satin or bright finish. The elastomer is available all the common colours of silicone.

The JF 600 range of control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints. The joints of the JF 600 range are used as control joints with adhesive-laid floor covering such as tiles, ceramics, etc. of 15 mm thickness or less. They are suitable for commercial and industrial uses. In general, control joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m. Made with coextruded PVC with an outer layer of rigid PVC for efficient protection of the tile edges, and a flexible PVC central element able the take up the floor constraints. The joints of the JF 600 range are used essentially for "budget" applications or when aesthetics is not a determining factor. Available in different heights and a length of 2.5 m. The control joints of the JF 600 range are available with long flanges or short flanges, in the standard grey, black and white colours. They can also be made with other heights, in any other RAL colour, and in any other special colour depending on quantity. The joints of the JF 600 range are used as control joints with adhesive-laid floor covering such as tiles, ceramics, etc. of 15 mm thickness or less. They are suitable for commercial and industrial uses. In general, bay joints are used to enclose areas between 25 m2 and 60 m2, with a maximum linear dimension between 5 m and 10 m.

The JF 700 range of pvc control joints has been designed to prevent problems, such as cracking and tile lifting, that will always appear when the floor covering is laid on large surfaces without any joints.

PVC control joints for floors made to prevent the malfunctions (cracks, debonding) that systematically occur when flooring systems are installed in large areas without joints. They are used to partition bed affixed floors such as tiles, ceramics, natural stone, etc. The PVC control joints are supplied with stainless steel or brass caps for a more luxurious finish.

The series JF Deco tile dividers are designed for decorating and dividing floors. They can also be used to get a better protection in accordance with different finishings (mill finish, polished, high gloss polished, etc.). Series JF Deco tile dividers are available in brass, aluminium and stainless steel.