Other products

Veda's butyl strip is a cold adhesive strip made up of an adhesive butyl backed by an aluminium-reinforced polyester film. The adhesive face is protected by a peel-off silicone backing and offers an excellent tear resistance. The butyl strip provides a water and vapour barrier. It is recommended for the repair of membrane tears or holes as well as the protection of mechanical joint anchors.

VED'EPDM (Ethylene Propylene Diene Monomer) membranes are made from high quality rubber. They are used to provide waterproofing for expansion joints. Economical, simple and easy to install, highly flexible and elastic, VED'EPDM is ideal for waterproofing expansion joints.

MS adhesive is designed for bonding and splicing VED'EPDM membranes. It is a high-strength, solvent-based contact adhesive for rapid bonding. It is specially formulated for application with a nap roller and/or thick brush. Its tack-free time makes it possible to treat large surfaces in a single operation.

VEDAFLEX SIL is a one-component silicone sealant of low modulus of elasticity and neutral cross-linkage. It vulcanises in contact with atmospheric moisture and forms a rubber that is extremely flexible and resistant. Non-corrosive, it does not produce substances with a strong odour.

Our expansion joint waterstop products are available in nitrile or flexible PVC (Vedaflex), elastomers which display different characteristics. Nitrile waterstops are characterised by a higher breaking point when stretched, excellent resistance to chemical agents as well as to ageing, and permanent elasticity that is comparable to that of rubber.

Internal profiles for waterproof expansion joints. Special clips and brass eyelets are available on request to facilitate installation. Use: Profile with central ring for internal expansion joints: expansion, contraction, shearing, settling movements, etc. Formwork accessories available on request.

Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings. Suitable for any type of base material: rough floors, painted floors, tiling, marble, stone, timber, aluminium, metal stairs, access ramps. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Rolls of different widths: 25 mm, 50 mm, 100 mm, 150 mm, other widths available between 9 mm and 1,000 mm. Standard rolls of 18.30 m. Roll of carborundum in standard colours: black, grey, white, yellow, clear, blue, green, red, brown or bright colours (fluorescent yellow...). Rolls or stripes in single or two colours black/yellow, red/white, etc. All Pantone and RAL colours or special colours according to quantities. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings.

All-aluminium step edge strip, NDM VD1 (40x20x3 mm) and NDM VD2 (55x33x3 mm). Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip surface. Suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Aluminium strip length of 3 m. Not drilled. Natural aluminium and anodised aluminium. Option of powder coating in RAL colour. Option of hot-melt adhesive stripes for fixing to floor. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.

Aluminium metal stair nosing, 100x35 mm, with two anti-slip carborundum inserts, held mechanically. Finishing strip for concrete stair treads or directly on floor covering. Ribbed anti-slip aluminium surface.
These metal stair nosing strips are suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.
Aluminium strip length of 3 m.
Black carborundum insert (other colours available) of 25 mm width, in rolls of 18.30m. Not drilled. Clear anodised aluminium. Fasteners under the inserts. Option of hot-melt adhesive stripes for fixing to floor. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Aluminium stair nosings, 100x35 mm, with two anti-slip carborundum inserts, held mechanically. Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip aluminium surface. Suitable for any type of construction.

Aluminium step edge strip, 68x43 mm, with black anti-slip flexible inserts Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip aluminium surface. Suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.

Metal stair nosing strips in 304 or 316L stainless steel (70x30 or 40x3 mm) with stripes or arabesques and undrilled. Finishing profiles for concrete steps or directly on flooring, can be used for all types of construction. These metal stair nosings are meant to be mechanically fixed every 290 mm and glued with MS adhesive. Perrfect for very heavy traffic and outdoor installation, these step edge strips ensure optimal protection of the stair treads nosings in heavy use situations and provide anti-slip protection to users.

Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings. Suitable for any type of base material: rough floors, painted floors, tiling, marble, stone, timber, aluminium, metal stairs, access ramps. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Rolls of different widths: 25 mm, 50 mm, 100 mm, 150 mm, other widths available between 9 mm and 1,000 mm. Standard rolls of 18.30 m. Roll of carborundum in standard colours: black, grey, white, yellow, clear, blue, green, red, brown or bright colours (fluorescent yellow...). Rolls or stripes in single or two colours black/yellow, red/white, etc. All Pantone and RAL colours or special colours according to quantities. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings.

All-aluminium step edge strip, NDM VD1 (40x20x3 mm) and NDM VD2 (55x33x3 mm). Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip surface. Suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Aluminium strip length of 3 m. Not drilled. Natural aluminium and anodised aluminium. Option of powder coating in RAL colour. Option of hot-melt adhesive stripes for fixing to floor. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.

In accordance with relevant standards (French SNJF and ISO), the joint backing is a material that is laid to limit the depth of the sealant in the joint and to define the back profile of the joint. It stops the sealant from adhering to the three faces of the joint and helps to resist the pressures that occur when apply the sealant. The joint backing must not have any effects that will change the physical and chemical properties, and even the appearance, of the sealant. It can eventually serve as a barrier to separate the sealant for chemical attacks from the bottom side of the joint. The joint backing is used as a permanent formwork when applying a sealant or any other finish. It is used to limit the depth of sealant that is applied. It is recommended for use with the following sealants: silicone, polyurethane, polysulphide, acrylic. Grey closed-cell polyethylene foam. Available in diameters from 10 mm to 50 mm, supplied in coils or in length according the the diameter used. Grey foam supplied in coils or lengths. The joint backing is used as a permanent formwork when applying a sealant or any other finish. It is used to limit the depth of sealant that is applied. It is recommended for use with the following sealants: silicone, polyurethane, polysulphide, acrylic.

Veda's butyl strip is a cold adhesive strip made up of an adhesive butyl backed by an aluminium-reinforced polyester film. The adhesive face is protected by a peel-off silicone backing and offers an excellent tear resistance. The butyl strip provides a water and vapour barrier. It is recommended for the repair of membrane tears or holes as well as the protection of mechanical joint anchors.

VED'EPDM (Ethylene Propylene Diene Monomer) membranes are made from high quality rubber. They are used to provide waterproofing for expansion joints. Economical, simple and easy to install, highly flexible and elastic, VED'EPDM is ideal for waterproofing expansion joints.

MS adhesive is designed for bonding and splicing VED'EPDM membranes. It is a high-strength, solvent-based contact adhesive for rapid bonding. It is specially formulated for application with a nap roller and/or thick brush. Its tack-free time makes it possible to treat large surfaces in a single operation.

Aluminium metal stair nosing, 100x35 mm, with two anti-slip carborundum inserts, held mechanically. Finishing strip for concrete stair treads or directly on floor covering. Ribbed anti-slip aluminium surface.
These metal stair nosing strips are suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.
Aluminium strip length of 3 m.
Black carborundum insert (other colours available) of 25 mm width, in rolls of 18.30m. Not drilled. Clear anodised aluminium. Fasteners under the inserts. Option of hot-melt adhesive stripes for fixing to floor. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Aluminium stair nosings, 100x35 mm, with two anti-slip carborundum inserts, held mechanically. Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip aluminium surface. Suitable for any type of construction.

Aluminium step edge strip, 68x43 mm, with black anti-slip flexible inserts Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip aluminium surface. Suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.

Metal stair nosing strips in 304 or 316L stainless steel (70x30 or 40x3 mm) with stripes or arabesques and undrilled. Finishing profiles for concrete steps or directly on flooring, can be used for all types of construction. These metal stair nosings are meant to be mechanically fixed every 290 mm and glued with MS adhesive. Perrfect for very heavy traffic and outdoor installation, these step edge strips ensure optimal protection of the stair treads nosings in heavy use situations and provide anti-slip protection to users.

VEDAFLEX SIL is a one-component silicone sealant of low modulus of elasticity and neutral cross-linkage. It vulcanises in contact with atmospheric moisture and forms a rubber that is extremely flexible and resistant. Non-corrosive, it does not produce substances with a strong odour.

Our expansion joint waterstop products are available in nitrile or flexible PVC (Vedaflex), elastomers which display different characteristics. Nitrile waterstops are characterised by a higher breaking point when stretched, excellent resistance to chemical agents as well as to ageing, and permanent elasticity that is comparable to that of rubber.

Internal profiles for waterproof expansion joints. Special clips and brass eyelets are available on request to facilitate installation. Use: Profile with central ring for internal expansion joints: expansion, contraction, shearing, settling movements, etc. Formwork accessories available on request.