Please tick your settings to determine the appropriate solutions.
ANTISLIP ADHESIVE TAPES
Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings. Suitable for any type of base material: rough floors, painted floors, tiling, marble, stone, timber, aluminium, metal stairs, access ramps. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Rolls of different widths: 25 mm, 50 mm, 100 mm, 150 mm, other widths available between 9 mm and 1,000 mm. Standard rolls of 18.30 m. Roll of carborundum in standard colours: black, grey, white, yellow, clear, blue, green, red, brown or bright colours (fluorescent yellow...). Rolls or stripes in single or two colours black/yellow, red/white, etc. All Pantone and RAL colours or special colours according to quantities. General and safety marking for buildings. Adhesive material to be stuck directly on the surface, which can previously be cleaned and treated with a bonding primer or an adhesive. For rough surfaces, aluminium plates are available to be fastened onto the surface. Anti-slip floor marking for all smooth or rough surfaces, in all types of environment, even if humid. Industrial and residential use, indoors et outdoors. General and safety marking in industrial, public and private buildings.
Learn moreNDM VD
All-aluminium step edge strip, NDM VD1 (40x20x3 mm) and NDM VD2 (55x33x3 mm). Finishing strip for concrete steps or directly on floor covering. Ribbed anti-slip surface. Suitable for any type of construction. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Aluminium strip length of 3 m. Not drilled. Natural aluminium and anodised aluminium. Option of powder coating in RAL colour. Option of hot-melt adhesive stripes for fixing to floor. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin. Step edges, on concrete or directly on finished floor covering. Strips held by fasteners every 30 cm, or ideally by chemical bonding using Vedpoxy resin.
Learn moreBACKER RODS
In accordance with relevant standards (French SNJF and ISO), the joint backing is a material that is laid to limit the depth of the sealant in the joint and to define the back profile of the joint. It stops the sealant from adhering to the three faces of the joint and helps to resist the pressures that occur when apply the sealant. The joint backing must not have any effects that will change the physical and chemical properties, and even the appearance, of the sealant. It can eventually serve as a barrier to separate the sealant for chemical attacks from the bottom side of the joint. The joint backing is used as a permanent formwork when applying a sealant or any other finish. It is used to limit the depth of sealant that is applied. It is recommended for use with the following sealants: silicone, polyurethane, polysulphide, acrylic. Recommended by SNJF (French institute for the classification of plastic and elastomeric sealants) as air and water seal in construction, as well as a seal in formworks. Grey closed-cell polyethylene foam. Available in diameters from 10 mm to 100 mm, supplied in coils or in length according the the diameter used. Grey foam supplied in coils or lengths. The joint backing is used as a permanent formwork when applying a sealant or any other finish. It is used to limit the depth of sealant that is applied. It is recommended for use with the following sealants: silicone, polyurethane, polysulphide, acrylic. Recommended by SNJF (French institute for the classification of plastic and elastomeric sealants) as air and water seal in construction, as well as a seal in formworks.
Learn moreBUTYL STRIP
Veda's butyl strip is a cold adhesive strip made up of an adhesive butyl backed by an aluminium-reinforced polyester film. The adhesive face is protected by a peel-off silicone backing and offers an excellent tear resistance. The butyl strip provides a water and vapour barrier. It is recommended for the repair of membrane tears or holes as well as the protection of mechanical joint anchors.
Learn moreCJ Alu
Our clip-affixed aluminium joint covers provide an aesthetical and decorative cost-effective solution. Our spring-clip system (available in different sizes: S, SLL, XL, XXL) allows an easy and fast installation. Our joint covers are suitable for joints gaps from 10 to 120 mm. They can be used for both new projects and refurbishment works, for indoor or outdoor configurations, for wall, ceiling and floor (pedestrian traffic only) joints.
Learn moreCJ Brass
Our clip-affixed brass joint covers provide an aesthetical and decorative solution. Our joint covers are available in different clip sizes for particular joint gaps, from 10 mm to 60 mm. These products are available from stock in 3m lengths, in flat section of 90 mm only. The Clip affixed brass joint covers are used in new constructions and in refurbishment projects, indoors or outdoors, in joints from 10-mm to 60-mm wide in walls, ceilings and floors (pedestrian use).
Learn moreCJ PVC
Our clip-on building expansion gaps covers in PVC can be used either indoors or outdoors wall expansion joints, ceilings and floors (light use). The expansion joint covers made for the floor are intended for a light use.
Learn moreCJ Stainless steel
The clip affixed stainless steel joint covers are designed to provide an attractive and decorative solution to the problem of protecting and concealing expansion joints (façades, walls and ceilings). Fast and easy to install: no drill or fixing required.
Learn moreCJE-PF
CJE-PF counterstunk joint cover is designed to protect and cover floor joints, but can also be used for facades, walls and ceilings. Aesthetic, decorative and economical, it can be used indoors or outdoors. Pre-drilled and countersunk, it is easy to install, and are used in new buildings and renovation projects for joints with openings from 10 to 250 mm.
Learn moreCJP
The CJP range of folded joint covers is designed to protect and cover joints in façades, walls, ceilings and floors. Economical, easy and quick to install, pre-drilled or plain, they are used in new constructions and in refurbishment projects, in expansion joints up to 500-mm wide, using flat or angle sections. Generally installed by mechanical means, they are drilled and countersunk in one side every 400 mm, i.e. 7 holes per 3-m bar.
Learn more